Diagnosis — general

1. Automatic transaxle malfunctions may be caused by five general conditions:

  1. ) Poor engine performance
  2. ) Improper adjustments
  3. ) Hydraulic malfunctions
  4. ) Mechanical malfunctions
  5. ) Malfunctions in the computer or its signal network

2. Diagnosis of these problems should always begin with a check of the easily repaired items: fluid level and condition (see Tune-up and routine maintenance), shift cable adjustment and shift lever installation. Next, perform a road test to determine if the problem has been corrected or if more diagnosis is necessary. If the problem persists after the preliminary tests and corrections are completed, additional diagnosis should be performed by a dealer service department or other qualified transmission repair shop. Refer to the Troubleshooting Section at the front of this manual for information on symptoms of transaxle problems.

Preliminary checks

3. Drive the vehicle to warm the transaxle to normal operating temperature.

4. Check the fluid level as described in Chapter Tune-up and routine maintenance:

  1. ) If the fluid level is unusually low, add enough fluid to bring the level within the designated area of the dipstick, then check for external leaks (see Fluid leak diagnosis below).
  2. ) If the fluid level is abnormally high, drain off the excess, then check the drained fluid for contamination by coolant. The presence of engine coolant in the automatic transmission fluid indicates that a failure has occurred in the internal radiator walls that separate the coolant from the transmission fluid (see Cooling, heating and air conditioning systems).
  3. ) If the fluid is foaming, drain it and refill the transaxle, then check for coolant in the fluid, or a high fluid level.

5. Make sure the engine idle speed is correct. If the idle speed is incorrect, have it adjusted by a dealer service department or other qualified repair shop before proceeding.

6. Inspect the shift cable. Make sure that it’s properly adjusted and operates smoothly (see Shift cable — replacement and adjustment).

Fluid leak diagnosis

7. Most fluid leaks are easy to locate visually. Repair usually consists of replacing a seal or gasket. If a leak is difficult to find, the following procedure may help.

8. Identify the fluid. Make sure it’s transmission fluid and not engine oil or brake fluid (automatic transmission fluid is a deep red color).

9. Try to pinpoint the source of the leak. Drive the vehicle several miles, then park it over a large sheet of cardboard. After a minute or two, you should be able to locate the leak by determining the source of the fluid dripping onto the cardboard.

10. Make a careful visual inspection of the suspected component and the area immediately around it. Pay particular attention to gasket mating surfaces. A mirror is often helpful for finding leaks in areas that are hard to see.

11. If the leak still cannot be found, clean the suspected area thoroughly with a degreaser or solvent, then dry it.

12. Drive the vehicle for several miles at normal operating temperature and varying speeds. After driving the vehicle, visually inspect the suspected component again.

13. Once the leak has been located, the cause must be determined before it can be properly repaired. If a gasket is replaced but the sealing flange is bent, the new gasket will not stop the leak. The bent flange must be straightened.

14. Before attempting to repair a leak, check to make sure that the following conditions are corrected or they may cause another leak.

Note: Some of the following conditions cannot be fixed without highly specialized tools and expertise. Such problems must be referred to a transmission shop or a dealer service department.

Seal leaks

15. If a transaxle seal is leaking, the fluid level or pressure may be too high, the vent may be plugged, the seal bore may be damaged, the seal itself may be damaged or improperly installed, the surface of the shaft protruding through the seal may be damaged or a loose bearing may be causing excessive shaft movement.

16. Make sure the dipstick tube seal is in good condition and the tube is properly seated. Periodically check the area around the speedometer gear or sensor for leakage. If transmission fluid is evident, check the 0-ring for damage.

Case leaks

17. If the case itself appears to be leaking, the casting is porous and will have to be repaired or replaced.

18. Make sure the oil cooler hose fittings are tight and in good condition.

Fluid comes out vent pipe or fill tube

19 If this condition occurs, the transaxle is overfilled, there is coolant in the fluid, the case is porous, the dipstick is incorrect, the vent is plugged or the drain-back holes are plugged.

  • Pages

    open all | close all